Calibration Facilities

1)

Calibration of Voltage, Current, resistance, capacitance, conductance frequency, time, temperature simulation  

Multifunction Calibration Systems Datron 9100 & Datron 9000, Wavetek make        
       

DC(V)

Upto 1050V

0.0005% of setting  

AC(V)

Upto 1050V

0.008% of setting  
DC(A)   1mA  to  1000A  

0.008% of setting

AC(A)   20mA to 1000A   0.0027% of setting  
Resistance   1W  to  400MW   0.006% of setting  
Capacitance   0.5nF  to  40mF   0.2% of setting  
Frequency   0.5Hz to10 MHz   0.25 ppm  

Temperature

-200 °C to 1350°C  

0.0025% of setting  

2)

Measurement of Resistance, Capacitance & Inductance   RLC  Digi Bridge GR 1689 Universal LCR Bridge Marconi, TF 1313 High Capacitance Meter Resistance Limit Bridge, GR 1652  

10MW to0.99MW

0.01pF to 0.99F

10m to 99999H  

±0.2%

±0.2%

±0.2%  

3)

Diode & Transistors

(DC Parameters only)  

Curve Tracer,

Philips, PM 6507

I cmax 20A

Vcc max 500V  

 

4)

Resistance Capacitance & Inductance  

Respective Standards available  

100mW to 1GW  
50pF to 10mF  
1mH to 10H  

±0.5%

±0.8%

±2%  

                5)

Calibration of Voltage

(DC & AC), Current (DC & AC), etc.  

 

Meter Calibration

Fluke 760 A,

Meter Calibrator, HP6920B  

DC(V) 1mV to

1000V AC(V) 1mV to 1000V 50/60/400Hz DC(A)1WmA to 10A AC(A) 1mA to 50A, 50Hz  

DC(V)- ±0.1% AC(V)-  ±0.02% to ±0.25% of reading

DC(A)- ±0.25%  AC(A) ±0.025% to

±0.25% 

6)

 

Power/Energy   Power/Energy Calibrator Rotek 811A   Power upto 749 Vx50A with leading & lagging loads in 0.1 steps. Freq.50/60/400 Hz Energy 24.5MW Sec.  

Power ±0.05% to ±0.22% of setting

Energy ±0.025% at 50/60Hz

±0.12% at 40Hz  

    7)

 

Calibration of Frequency & Time   Frequency counter Scientific HM 5021-3/HM 8021-2 Frequency counter PM 6668, Philips Function Generator Scientific HM 8030-4  

Upto 1GHz

0.3Hz to 1GHz  

 

±5x10-7  

    8)

 

Solder ability   Temperature controlled Soldering Iron (Waller) & Solder Bath (Rotadip)   Upto 450 °C      
    9) System/Subsystem Testing  

Oscilloscope CRO 100 MHz Insulation Tester, Breakdown Tester DMM61/2 Digit HP 34401A High Voltage Tester  

upto 100KVAC   +2%  
   10)   Environmental Facilities   Dry Heat Chamber, Dry Cold Chamber Damp Heat Chamber   150°C upto       -20°C RH upto 98% Temperature upto 90°C  

±3°C

±3°C

±0.5°C

    11)

Calibration of RPM

Digital Tachometer upto 10,00,000 RPM   ±1Rpm  
    12) Calibration of Pressure   Digital Pressure Meter, Pressure Calibrators   -85 to 700 kg/cm.sq.   ±0.5%  
    13)

Calibration of Temperature

Temperature Calibrator   Ambient to 1200°C    

    14)

 

Calibration of Length   Micrometer & Verniers, Slip Gauges   Upto 600mm ±5m  

    15)

 

Calibration of Oscilloscope   Meter Calibration System Datron-9100   Time base 250MHz Bandwidth -250 MHz  

±0.25 ppm

 

±1.5% to 3%  

 16)   Calibration of pH Meters  

Microprocessor based pH meter CP931

 

0 to 14 pH

Temperature 

-100°C to  +200°C  

 

0. ±01pH

±1Digit

±0.1%

±1Digit

17)

Calibration of conductivity meter

 

Microprocessor based conductivity meter CC631  

0-200 mS

Temp. -100°C to 200°C  

±0.5%

±1Digit

±0.1%

±1Digit  

 

Facilities for calibration of electro-medical equipments like ECG machine, Defibrillator, Beside Monitor, Electro Surgical Units, Blood Pressure & Respiratory Rate Meters, Phototheraphy equipments are also available.

Calibrators in the Pipe-line:

  • Standard RF Signal Generator

  • Standard RF power meter.

  • Standard torque wrench.

  • Thread plug and thread ring gauge calibrators.

  • Standard plating thickness measurement unit.

    Sample list of Equipments Calibrated:

  • Panel meter, Analog/Digital Multimeter, Voltmeter, Ammeter, Wattmeter, Energy meter, LUCRE Bridge/Meter, Milli-Ohm/Micro-Ohm meter, Resistance/Capacitance/Inductance boxes, Electrical/Electronic load.

  • Signal Generator, Level Generator, Function Generator, Analog/Digital Oscilloscope, Frequency meter/Counter, Attenuator, dB meter, Distortion meter.

  • HV Break down tester, Oil test set, Wheat stone bridge, Kelvin's double bridge, Potentiometer, Megger, Tong tester, Leakage current tester, Current/Potential Transformer, Power supplies, Ratio meter.

  • Tachometer, pH meter, Conductivity meter, Electronic Weigh balance, Verniers, Micrometer/Screw Gauge, Stopwatch, Chart/X-Y/Strip recorders, Pressure/Vacuum Gauge, Process Calibrator, mA/mV Source etc.

  • Temperature sensor/indicators/recorders/baths, temperature simulators.


Copyright © 2004 MPSEDC, Bhopal. All rights reserved.